Search found 418 matches

by Mark
Fri Jul 01, 2016 2:28 am
Forum: General Discussion
Topic: Temperature reading off - calibration possible?
Replies: 26
Views: 17876

Re: Temperature reading off - calibration possible?

OK, I've just uploaded a modified version of the firmware to fix this - you can download it from here: http://www.ultrasmartcharger.com/TemperatureFix.zip To use this version, you need to unzip the above file, start a command prompt and run the doflash batch file, passing the COM port to it - e.g. d...
by Mark
Fri Jul 01, 2016 12:56 am
Forum: General Discussion
Topic: Temperature reading off - calibration possible?
Replies: 26
Views: 17876

Re: Temperature reading off - calibration possible?

Peter and Martin,

Can you provide the serial numbers from all of your chargers please? It sounds like you have each received a pair of chargers that weren't made at the same time...
by Mark
Thu Jun 30, 2016 1:32 pm
Forum: General Discussion
Topic: Temperature reading off - calibration possible?
Replies: 26
Views: 17876

Re: Temperature reading off - calibration possible?

Sorry I didn't get a chance to work on this yet again. I did talk to Paul via email and he thinks that it's possible that some different temperature sensors might have slipped in on some chargers - I've asked him to check the self test logs to try to work out the range of serial numbers affected so ...
by Mark
Thu Jun 30, 2016 5:29 am
Forum: General Discussion
Topic: saving full data
Replies: 6
Views: 5147

Re: saving full data

Try clicking on the "Chart" tab and see if you can see the export button there?
by Mark
Thu Jun 30, 2016 4:58 am
Forum: General Discussion
Topic: higher charge/discharge current via external
Replies: 5
Views: 3933

Re: higher charge/discharge current via external

OK, I'll try and do that as well later today.

You should be able to control the current through the manager - it might require modified firmware though - let me get back to you about that.
by Mark
Thu Jun 30, 2016 4:57 am
Forum: General Discussion
Topic: saving full data
Replies: 6
Views: 5147

Re: saving full data

I've just checked and the version that you can download should be correct.

Can you post a screenshot of what you are seeing perhaps?
by Mark
Thu Jun 30, 2016 12:14 am
Forum: General Discussion
Topic: higher charge/discharge current via external
Replies: 5
Views: 3933

Re: higher charge/discharge current via external

Yes, just below each of the 2 ohm resistors at the top of the board is the connection for the external load - keep in mind that the external load will run in parallel to the 2 ohm resistor. External power which bypasses the poly fuse can supplied through the connection points either side of the USB ...
by Mark
Thu Jun 30, 2016 12:12 am
Forum: General Discussion
Topic: saving full data
Replies: 6
Views: 5147

Re: saving full data

You should be able to save the data by clicking on the Export button in the top right corner of the program - keep in mind that this will only export the data that is currently being shown on the screen. If you want everything from multiple charge/discharge cycles, it would be best to insert and SD ...
by Mark
Thu Jun 30, 2016 12:10 am
Forum: General Discussion
Topic: Temperature reading off - calibration possible?
Replies: 26
Views: 17876

Re: Temperature reading off - calibration possible?

OK, I'll need to work on this ASAP - I'll try to get it done today for both of you.
by Mark
Tue Jun 21, 2016 10:11 pm
Forum: General Discussion
Topic: Temperature reading off - calibration possible?
Replies: 26
Views: 17876

Re: Temperature reading off - calibration possible?

OK, no worries.

I'm fairly busy at the moment, so I probably won't get a chance to work on the firmware for a few days anyway.